The hanger is in charge of holding the exhaust pipe to your Volvo’s frame. It is usually positioned near the back of your Volvo. The exhaust pipes hold a good amount of space within and through your Volvo’s exhaust system. These exhaust pipes, which can be metal or aluminum, are in control of distributing the burning exhaust fumes from the engine and exhaust manifold and pushing them through your Volvo’s tailpipe. FCP Euro’s well-versed and skilled call center staff is always available and ready to answer any questions you have. If you are not totally confident about which exhaust pipe parts or component is required for your Volvo, FCP has a massive line up for the Volvo brand. Check out the FCP Euro website for all parts, as well as our updated inventory. If you have questions, would like to put in a phone order, or just have feedback, do not waver in giving FCP Euro a call at to connect with our service friendly team.
Exhaust Flex Connector Extension Pipes FORTLUFT consists of four layers. The outer and inner layers are made from the weaving stainless wire. Between these layers, there is a double layer bellow, also made of stainless steel. Standard Caps with connectors are installed on both sides of the exhaust flex pipe. They securely fasten all four layers and allow them to integrate this spare part into the exhaust system by welding pipes or clamps. Our Verocious Motorsports Universal Exhaust Flex Pipes are your solution for cracked exhaust pipes. Whether repairing damaged OEM exhausts or building a custom exhaust, our high quality stainless steel flex couplers are more than capable of handling the job.
If the flex pipe comes separate from the catalytic converter, an average replacement cost might be about $400 at a general repair shop. If the flex pipe is replaced with the catalytic converter, the average repair cost might be about $1500. A flex pipe allows a little more freedom in exhaust system design and a little better noise and vibration absorption in the engine mount system. Usually, the flex pipe is a short section of exhaust made from a flexible accordion pipe and protected with a braided wire covering. If you notice any of these signs, you may have a flex pipe exhaust leak. It’s extremely important to replace your flex pipe because a broken one can cause serious damage to your exhaust system. One of the reasons you should consider fixing your exhaust pipe right away is fuel economy. The exhaust serves as a critical part of the vehicle that helps to remove fumes. So, if there is an issue with the exhaust of your car, you should expect a reduction in fuel efficiency. Remember that you don’t have to take down your exhaust to fix it.
It could also be a result of rusting, which would weaken the strength of the exhaust pipe and cause it to break easily. The reason this is important is due to the natural laws of physics. When the metal piping of an exhaust system and headers heats from the hot exhaust gasses passing through it, that metal expands. In the reverse, after the engine is shut off, that piping cools, and the metal contracts. Exhaust flex pipe sections are widely available at automotive stores in a variety of lengths and diameters. To answer my own question, while flexpipe does flex, it is not meant to be flexed more than a very minimal amount, enough to compensate for any vibrations in the exhaust system. I tried very gently to flex it and it only moved a drop, so I went another route because I din’t want to bust the pipe.
Quietlife dry exhaust pipe, although flexible, should not be bent in extreme angles as this may cause the product to not be gas tight. We recommend that hot surfaces like dry exhaust pipe should be insulated with exhaust lagging. It is suitable for use in a marine dry exhaust system due to its construction and durability. This exhaust pipe is designed to run inline as a flexible section of pipe between the engine and rigid exhaust piping. Our titanium flex tubes are manufactured from the highest quality grade 2 titanium. The titanium flex pipe is to compensate for temperature expansions and vibrations in the exhaust system. Loosen and slide back the U-bolt assembly to access the slip joint between the short muffler pipe that slips over the exhaust pipe, or vise versa. Clean the connection with a wire brush and clean with acetone. Apply a high-quality tape wrap in at least 3 layers and cure with heat to bond the tape to itself and the exhaust pipes. I have used reinforcement tape that cures by chemical process to repair yard tool handles, but don’t know if it will withstand the exhaust heat.
If it is still warm, the engine and exhaust are both still extremely hot. The exhaust piping in your vehicle can reach extremely high temperatures while the engine is running. Allow the vehicle to cool for a few hours before attempting to work on the exhaust to avoid burning yourself. An exhaust leak will cause noise first when the engine starts and under heavy acceleration, and then more continually if the part is allowed to fail entirely. The first step in diagnosing a catalytic converter or O2 sensor code is inspecting the exhaust system for leaks. The critical part of the flex pipe that fails is the inner accordion-bent pipe, and there is no practical way to reliably repair it. The above flex pipe repair cost estimates are for certified parts. If those weren’t required, then, some small amount of savings on non-certified parts would be possible. The labor time to replace the flex pipe is estimated at 1.2 hours.
Once the bolts have been taken away, pull out the exhaust manifold from the engine. FCP has a huge line up of updated Volvo Exhaust Pipe parts including, Volvo Header Part Parts, Volvo Exhaust Pipe Axle Parts, all Volvo Exhaust Header parts. If you have questions about Volvo’s exhaust pipe parts or components, the FCP Euro team and website are always there for you. And whether exhaust flexible pipe bellows is equal, reducing, or . Automotive exhaust pipes get extremely hot from the exhaust gas passing through the system and out the tailpipe. Due to this, when an exhaust system needs to bend, shift or be flexible, the manufacturer cannot use traditional materials like rubber. The flex pipe is made of metal strips woven into a lattice, and thus can withstand exhaust gas heat.
To determine “Natural Lie,” bend the tube as much as possible against the edge of the work bench. Now push the entire tubing against the table until straight to reach its half extension, or natural lie. For optimal installation, install tubing in its “Natural Lie” state, midway between fully compressed and fully extended. This provides the most workable range and the longest service life of the installed flex tubing. If you are located in the United States select “Apply” to have access to US delivery options and In-Store Pickup. If you are an international customer who ships to a US address choose “United States delivery” and we will estimate your ship dates accordingly.
Flex pipes are an essential piece of equipment for any front wheel drive vehicle and on most all-wheel-drive vehicles. For front wheel drive cars, the motor is mounted transversely. So when you accelerate, the motor rocks and the flex pipe protects your exhaust system from breaking. Without that extra flexibility, the rocking motion would crack your exhaust system. That’s what causes the loud leak when your exhaust bellows malfunction. Firstly, it is possible to fix an exhaust pipe if you cannot weld or don’t have a welder nearby. There are also different ways to fix an exhaust based on the gravity of the damage. Give the exhaust some time to cool down and then proceed to inspect the damage. If what you have is a broken exhaust pipe, a flex pipe and two clamps will do the job.
Most shops will be limited to bolting on OE-style parts. An exhaust shop, on the other hand, would have more options as far as fabricating or adapting cheaper universal parts, if state regulations allow. This post is all about how to fix exhaust pipe without welding. I understand welding or getting a new exhaust could be quite expensive. But this method I have just highlighted won’t get you to break the bank. The process is also quick and straightforward, as you can see from the explanation. It will buy you some more time to save up for a new exhaust or do other repairs on your exhaust pipe.